10-11-2013, 12:58 AM | #1 |
Nade Whore
Server Owner
Beta Tester Join Date: Sep 2007
Location: Oklahoma
Class/Position: Scout/Soldier Gametype: CTF/TDM Affiliations: blunt. Moto Posts Rated Helpful 128 Times
|
Rounded corners on a wall
I'm new to mapping and I've been trying different methods to achieve this so I was wondering if it were even possible.
I have a 16 unit thick wall that has a half cylinder on top of it with 6 sides. The same wall has another half cylinder with 6 sides. Currently there is a gap where the 2 cylinders meet and I want to make a rounded corner that will fit each of those 6 sides on both cylinder ends perfectly. Is there a way to do this? I've tried spheres, displacements/subdividing/clipping and nothing seems to work. The closest I can get is by creating a sphere but I think the fact that my wall is 16 units thick and the cylinder has 12 points before I cut it in half that when I try making a sphere 16 units wide with 12 points, it doesn't quite look like a sphere. I can make a 6 point sphere fine but when I clip it into its quarter, it doesn't match up with the 6-sided cylinder ends. I've checked the interlopers site as well as some other resource/tutorial sites with no luck. Here's a couple images of what I'm talking about: |
|
10-11-2013, 01:10 AM | #2 |
#FF.Pickup Dictator
Beta Tester
Join Date: Aug 2011
Location: Detroit
Gametype: ADL Affiliations: KiNGz . Posts Rated Helpful 100 Times
|
I'm very new to hammer so I could be wrong. I don't think what you're describing is possible.
But I think youd have better luck lining them up if you cut them and made them "rounded" yourself so that all the lines would be on the grid. Then pull the horizontal one forward above the vertical one and make cuts from the top that line up with the vertical one. Last edited by aleXtric; 10-11-2013 at 01:12 AM. |
|
10-11-2013, 02:58 AM | #3 |
Nade Whore
Server Owner
Beta Tester Join Date: Sep 2007
Location: Oklahoma
Class/Position: Scout/Soldier Gametype: CTF/TDM Affiliations: blunt. Moto Posts Rated Helpful 128 Times
|
Ok so I finally got it. I followed this tutorial:
And while the overall end product is different, it was made using the same principle. After some tinkering with vertices I was able to get it all lined up with the existing cylinder ends. Still, it'd be nice if hammer had a way to make this process easier. Now I just need to figure out how to match the faces of those textures to the faces on the cylinders. Last edited by KubeDawg; 10-11-2013 at 03:00 AM. |
|
10-12-2013, 07:10 PM | #4 |
Beta Tester
Join Date: Jul 2008
Posts Rated Helpful 144 Times
|
I think you can fake roundovers with displacements? Displacement master squeek might know. I think (emphasis think) displacements get a phong interpolation pass which more or less smooths out edges. Other than that you can use models, which allow a high poly count and support phong interpolation. You can kinda fake rounding with clever use of bumpmaps as well. Neither of the last two options are easy but when you see amazing looking source maps that's probably what the mappers are doing.
Last edited by the_cake; 10-12-2013 at 07:11 PM. |
|
10-13-2013, 04:07 PM | #5 |
worst ff player eu
Join Date: Jun 2012
Location: South Yorks., England
Class/Position: o - no, d - scout Gametype: IvDZ Posts Rated Helpful 18 Times
|
Pro tip: Putting too much detail in a map is completely useless and a lot of people who are new to mapping do it!
Literally, look at any good map made by anyone and it has almost no rounded edges (closest you get is slightly curved edges on ksour) and misaligned textures. No-one actually cares to look while they're playing, so...
__________________
gg ff not ded ff very much alive |
|
10-13-2013, 04:37 PM | #6 | |
Beta Tester
Join Date: Nov 2011
Gametype: Capture the Flag Posts Rated Helpful 293 Times
|
Quote:
__________________
Currently equipped: Rad Scarf of liberating happiness. |
|
|
10-13-2013, 06:29 PM | #7 |
Join Date: Jun 2011
Location: USA
Class/Position: Soldier & Medic Affiliations: ( ir :: ) iv| K^ † Posts Rated Helpful 80 Times
|
Yeah, no one even notices the untextured bits in tidalwave, but we play it all the time. Fu FDgay
__________________
|
|
10-13-2013, 06:31 PM | #8 |
Nade Whore
Server Owner
Beta Tester Join Date: Sep 2007
Location: Oklahoma
Class/Position: Scout/Soldier Gametype: CTF/TDM Affiliations: blunt. Moto Posts Rated Helpful 128 Times
|
Well technically it's not a rounded edge, but has 6 sides with 6 15 degree angle slices, each at different angles, that make it look rounded. I know it's probably not that big of a deal, but this is FF, not Minecraft. A blocky looking map does not look good.
|
|
10-13-2013, 06:31 PM | #9 | |
Beta Tester
Join Date: Nov 2011
Gametype: Capture the Flag Posts Rated Helpful 293 Times
|
I have a tendency to rush maps so I can see how they play. That doesn't mean a more detailed job would go unappreciated.
Quote:
__________________
Currently equipped: Rad Scarf of liberating happiness. Last edited by FDA_Approved; 10-13-2013 at 06:32 PM. |
|
|
10-13-2013, 10:30 PM | #10 |
Jay|mOfO|Mills
Beta Tester
Join Date: Feb 2009
Location: Santa Fe, NM
Gametype: Snag the flag beotches Posts Rated Helpful 8 Times
|
My two cents
Kube, I appreciate a mapper that takes some time and adds trims and rounds edges and takes a minute to make their map look nice. No it may not add to gameplay, but anybody who makes maps will notice.
That aside, it may not be the fix you wanted but here is an easier way to do it taking the picture you uploaded into consideration. lets assume the rounded corner you have missing and want to create is a 16x16 space. Take the top rounded portion (16x however long) and the side rounded portion and copy a 16x16 section of each that overlaps on the corner(the empty space you want to fill). Use the clipping brush on a 45 degree angle to cut out 1/2 of each block so it tapers the direction you want. This will make the corner meet and keep the curve of each wall but not make a complete rounded corner. If your rounded corners were created the same they will line up peachy and you will save a ton of time. Otherwise I'd use the torus tool and clip off what you dont need.... Displacements also will work but if you dont do it correctly (i.e. make 6 copies of the displacement then only use the middle one) the outside edges will not really be curves. Make sure you make that stuff func_detail Interlopers has great tutorials for this kind of stuff |
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|